{
  "dock_tip_0x00010001": {
    "en": "Right joystick abnormal, please release the joystick or calibrate the remote controller",
    "zh": "右摇杆异常，请松开摇杆或校准遥控器"
  },
  "dock_tip_0x00010002": {
    "en": "Left joystick abnormal, please release the joystick or calibrate the remote controller",
    "zh": "左摇杆异常，请松开摇杆或校准遥控器"
  },
  "dock_tip_0x00010003": {
    "en": "Right throttle stick abnormal, please release the throttle stick or calibrate the remote controller",
    "zh": "右波轮异常，请松开波轮或校准遥控器"
  },
  "dock_tip_0x00010004": {
    "en": "Left throttle stick abnormal, please release the throttle stick or calibrate the remote controller",
    "zh": "左波轮异常，请松开波轮或校准遥控器"
  },
  "dock_tip_0x00010005": {
    "en": "Remote controller battery temperature too high, please cool down before charging",
    "zh": "遥控器电池温度过高，请降温后充电"
  },
  "dock_tip_0x00010006": {
    "en": "Remote controller battery temperature too low, please warm up before charging",
    "zh": "遥控器电池温度过低，请升温后充电"
  },
  "dock_tip_0x10000F01": {
    "en": "Network module version does not match the aircraft. Please check and upgrade.",
    "zh": "网络模块版本与飞机不一致，请检查并升级"
  },
  "dock_tip_0x1001": {
    "en": "Abnormal motor power supply",
    "zh": "电机电源异常"
  },
  "dock_tip_0x1002": {
    "en": "Abnormal servo power supply",
    "zh": "舵机电源异常"
  },
  "dock_tip_0x2003": {
    "en": "Cabin internal temperature and humidity sensor communication abnormal",
    "zh": "舱内温湿度传感器通讯异常"
  },
  "dock_tip_0x2004": {
    "en": "Lower cabin water immersion sensor abnormal",
    "zh": "下舱水浸传感器异常"
  },
  "dock_tip_0x2005": {
    "en": "Vibration sensor abnormal",
    "zh": "振动传感器异常"
  },
  "dock_tip_0x2006": {
    "en": "Backup battery communication abnormal",
    "zh": "备用电池通讯异常"
  },
  "dock_tip_0x2007": {
    "en": "Weather station communication abnormal",
    "zh": "气象站通讯异常"
  },
  "dock_tip_0x2008": {
    "en": "Charging main module communication abnormal",
    "zh": "充电主模块通讯异常"
  },
  "dock_tip_0x2009": {
    "en": "Charging sub-module communication abnormal",
    "zh": "充电副模块通讯异常"
  },
  "dock_tip_0x2012": {
    "en": "Abnormal Nest–aircraft communication. Please check charging pin contact and battery status.",
    "zh": "机巢与飞机电池通讯异常，请检查充电脚架的接触情况和电池状态"
  },
  "dock_tip_0x2013": {
    "en": "Warning of water immersion",
    "zh": "水浸告警"
  },
  "dock_tip_0x2014": {
    "en": "Abnormal vibration alarm of machine nest",
    "zh": "机巢异常振动告警"
  },
  "dock_tip_0x2015": {
    "en": "Abnormal landing lights",
    "zh": "着陆灯异常"
  },
  "dock_tip_0x2016": {
    "en": "Abnormal communicate of UPS power",
    "zh": "UPS电源通讯异常"
  },
  "dock_tip_0x2017": {
    "en": "Abnormal of UPS power supply",
    "zh": "UPS电源异常"
  },
  "dock_tip_0x2018": {
    "en": "Abnormal communicate of power adapter",
    "zh": "电源适配器通讯异常"
  },
  "dock_tip_0x2019": {
    "en": "Power adapter abnormality, backup battery in use",
    "zh": "电源适配器异常，当前由备用电池供电。"
  },
  "dock_tip_0x201A": {
    "en": "Failed to communicate of motor driver board",
    "zh": "电机驱动板通讯失败"
  },
  "dock_tip_0x201B": {
    "en": "Motor driver board abnormal reset",
    "zh": "电机驱动板异常复位"
  },
  "dock_tip_0x2025": {
    "en": "Cabin external temperature and humidity sensor communication abnormal",
    "zh": "舱外温湿度传感器通讯异常"
  },
  "dock_tip_0x2035": {
    "en": "Abnormal Nest–aircraft communication. Please check wireless charging alignment and battery status.",
    "zh": "机巢与飞机电池通讯，请检查无线充电接触对位及电池当前状态"
  },
  "dock_tip_0x2036": {
    "en": "Left hatch obstructed. Please check for obstructions and then open or close the hatch again.",
    "zh": "左舱门受阻，请检查是否有异物遮挡，然后重新开合舱门"
  },
  "dock_tip_0x2037": {
    "en": "Right hatch obstructed. Please check for obstructions and then open or close the hatch again.",
    "zh": "右舱门受阻，请检查是否有异物遮挡，然后重新开合舱门"
  },
  "dock_tip_0x2039": {
    "en": "Abnormal communication of rain gauge sensor",
    "zh": "雨量传感器通讯异常"
  },
  "dock_tip_0x20700001": {
    "en": "The alternate landing point is over 50 m from the nest. Set another point.",
    "zh": "备降点与机巢距离超过50m，请重新设置备降点"
  },
  "dock_tip_0x20700002": {
    "en": "Network RTK login failed. Check the account and server.",
    "zh": "网络RTK登录失败，请检查账号和服务器"
  },
  "dock_tip_0x20700003": {
    "en": "Network RTK connection unstable, differential data interrupted. Check whether the account is used by multiple devices.",
    "zh": "网络RTK连接不稳定，差分数据中断，请检查账号是否被多端使用"
  },
  "dock_tip_0x20700004": {
    "en": "Nest RTK has not reached a fixed solution for a long time. Retry later or restart the nest.",
    "zh": "机巢RTK长时间未达到固定解，请稍后重试或重启机巢"
  },
  "dock_tip_0x20700005": {
    "en": "Magnetic encoder paddle abnormal, visual paddle enabled.",
    "zh": "磁编转桨异常，启用视觉转桨"
  },
  "dock_tip_0x20700006": {
    "en": "Long-time recording detected while aircraft is docked; recording has been stopped automatically.",
    "zh": "检测到飞机在机巢内长时间录像，已自动停止"
  },
  "dock_tip_0x20700007": {
    "en": "Nest system time is out of sync with the cloud. Check the nest time settings.",
    "zh": "机巢系统时间与云端不同步，请检查机巢时间设置"
  },
  "dock_tip_0x20700008": {
    "en": "Nest storage usage is too high. Clean up storage space promptly.",
    "zh": "机巢存储空间使用率过高，请及时清理存储空间"
  },
  "dock_tip_0x2211": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2212": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x221F": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2221": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2222": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2223": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2224": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2225": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2226": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2227": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2228": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x222F": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2231": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2232": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2233": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2234": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2235": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2236": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2237": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2238": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2239": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x223F": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x2300": {
    "en": "Wireless charging error. Please ensure the aircraft is properly centered, then restart the nest. If the issue persists after restarting, please contact after-sales support.",
    "zh": "无线充电异常，请确认飞行器已归中后重启机巢；若重启后仍有故障，请联系售后支持"
  },
  "dock_tip_0x30000503": {
    "en": "Low battery. Returning to takeoff point for landing.",
    "zh": "飞机电量低，正在执行备降飞往起飞点降落"
  },
  "dock_tip_0x30000504": {
    "en": "Critical low battery. Executing emergency landing.",
    "zh": "严重低电量，正在执行备降"
  },
  "dock_tip_0x3001": {
    "en": "Blocked wh op ing hatch",
    "zh": "开门时舱门阻塞"
  },
  "dock_tip_0x3002": {
    "en": "Blocked wh closing hatch",
    "zh": "关门时舱门阻塞"
  },
  "dock_tip_0x3003": {
    "en": "Abnormal op ing door",
    "zh": "开门异常"
  },
  "dock_tip_0x3004": {
    "en": "Abnormal closing door",
    "zh": "关门异常"
  },
  "dock_tip_0x3005": {
    "en": "Blocked wh X-rod returns to c ter",
    "zh": "X杆归中时阻塞"
  },
  "dock_tip_0x3006": {
    "en": "Blocked wh X-rod released",
    "zh": "X杆释放时阻塞"
  },
  "dock_tip_0x3007": {
    "en": "Abnormal of X-rod returns to c ter",
    "zh": "X杆归中异常"
  },
  "dock_tip_0x3008": {
    "en": "Abnormal of X-rod released",
    "zh": "X杆释放异常"
  },
  "dock_tip_0x3009": {
    "en": "Blocked wh Y-rod returns to c ter",
    "zh": "Y杆归中时阻塞"
  },
  "dock_tip_0x300A": {
    "en": "Blocked wh Y-rod released",
    "zh": "Y杆释放时阻塞"
  },
  "dock_tip_0x300B": {
    "en": "Abnormal of Y-rod returns to c ter",
    "zh": "Y杆归中异常"
  },
  "dock_tip_0x300C": {
    "en": "Abnormal of Y-rod released",
    "zh": "Y杆释放异常"
  },
  "dock_tip_0x300D": {
    "en": "Abnormal of Z-rod raised",
    "zh": "Z杆竖起异常"
  },
  "dock_tip_0x300E": {
    "en": "Abnormal of Z-rod fall down",
    "zh": "Z杆倒下异常"
  },
  "dock_tip_0x300F": {
    "en": "Abnormal of limit switch",
    "zh": "限位开关异常"
  },
  "dock_tip_0x3010": {
    "en": "Abnormal of motor hatch",
    "zh": "舱门电机异常"
  },
  "dock_tip_0x3011": {
    "en": "Abnormal of X-rod motor",
    "zh": "X杆电机异常"
  },
  "dock_tip_0x3012": {
    "en": "Abnormal of Y-rod motor",
    "zh": "Y杆电机异常"
  },
  "dock_tip_0x3013": {
    "en": "Z-rod (propeller lever)  servo 1 abnormal",
    "zh": "Z杆(拨桨杆)舵机1异常"
  },
  "dock_tip_0x3014": {
    "en": "Z-rod (propeller lever) servo 2 abnormal",
    "zh": "Z杆(拨桨杆)舵机2异常"
  },
  "dock_tip_0x3015": {
    "en": "Z-rod (propeller lever) servo 3 abnormal",
    "zh": "Z杆(拨桨杆)舵机3异常"
  },
  "dock_tip_0x3016": {
    "en": "Z-rod (propeller lever)  servo 4 abnormal",
    "zh": "Z杆(拨桨杆)舵机4异常"
  },
  "dock_tip_0x30900001": {
    "en": "The mechanical arm X-axis motor 6 abnormal. Contact after-sales service for assistance.",
    "zh": "机械臂X轴6号电机异常，请联系售后处理"
  },
  "dock_tip_0x30900002": {
    "en": "The mechanical arm Y-axis motor 7 abnormal. Contact after-sales service for assistance.",
    "zh": "机械臂Y轴7号电机异常，请联系售后处理"
  },
  "dock_tip_0x30900003": {
    "en": "The mechanical arm Z-axis motor 8 abnormal. Contact after-sales service for assistance.",
    "zh": "机械臂Z轴8号电机异常，请联系售后处理"
  },
  "dock_tip_0x30900004": {
    "en": "The platform reports motor abnormalities. Contact after-sales service for assistance.",
    "zh": "平台推出电机异常，请联系售后处理"
  },
  "dock_tip_0x30900005": {
    "en": "Left door motor abnormality.Contact after-sales service for assistance.",
    "zh": "左门电机异常，请联系售后处理"
  },
  "dock_tip_0x30900006": {
    "en": "Platform lift left motor abnormality.Contact after-sales service for assistance.",
    "zh": "平台升降左电机异常，请联系售后处理"
  },
  "dock_tip_0x30900007": {
    "en": "Lift platform abnormality.Contact after-sales service for assistance.",
    "zh": "升降平台异常，请联系售后处理"
  },
  "dock_tip_0x30900008": {
    "en": "Robotic arm gripper abnormality.Contact after-sales service for assistance.",
    "zh": "机械臂爪手异常，请联系售后处理"
  },
  "dock_tip_0x30900009": {
    "en": "Motor abnormality.Contact after-sales service for assistance.",
    "zh": "电机异常，请联系售后处理"
  },
  "dock_tip_0x30900010": {
    "en": "Right door motor abnormality.Contact after-sales service for assistance.",
    "zh": "右门电机异常，请联系售后处理"
  },
  "dock_tip_0x30900011": {
    "en": "Platform lift right motor abnormality.Contact after-sales service for assistance.",
    "zh": "平台升降右电机异常，请联系售后处理"
  },
  "dock_tip_0x30900012": {
    "en": "Robotic arm X-axis abnormality.Contact after-sales service for assistance.",
    "zh": "机械臂X轴异常，请联系售后处理"
  },
  "dock_tip_0x30900013": {
    "en": "Robotic arm Y-axis abnormality.Contact after-sales service for assistance.",
    "zh": "机械臂Y轴异常，请联系售后处理"
  },
  "dock_tip_0x30900014": {
    "en": "Robotic arm Z-axis abnormality.Contact after-sales service for assistance.",
    "zh": "机械臂Z轴异常，请联系售后处理"
  },
  "dock_tip_0x30900015": {
    "en": "Servo communication error.Contact after-sales service for assistance.",
    "zh": "舵机通讯错误，请联系售后处理"
  },
  "dock_tip_0x30900016": {
    "en": "The machine nest is in emergency stop. Reset the software emergency stop button before operating the equipment.",
    "zh": "机巢急停中，请复位软件急停按钮后再操作设备"
  },
  "dock_tip_0x30900017": {
    "en": "X-axis home positioning rod abnormality.Contact after-sales service for assistance.",
    "zh": "X轴归中杆异常，请联系售后处理"
  },
  "dock_tip_0x30900018": {
    "en": "Platform Y-axis motor 5 abnormality.Contact after-sales service for assistance.",
    "zh": "平台Y轴5号电机异常，请联系售后处理"
  },
  "dock_tip_0x30900019": {
    "en": "Y-axis home positioning rod abnormality.Contact after-sales service for assistance.",
    "zh": "Y轴归中杆异常，请联系售后处理"
  },
  "dock_tip_0x30900020": {
    "en": "Z2 load limit abnormality.Contact after-sales service for assistance.",
    "zh": "Z2负载限制异常，请联系售后处理"
  },
  "dock_tip_0x30900021": {
    "en": "Robotic arm Z2 axis abnormality.Contact after-sales service for assistance.",
    "zh": "机械臂Z2轴异常，请联系售后处理"
  },
  "dock_tip_0x30900022": {
    "en": "Z1 load limit abnormality.Contact after-sales service for assistance.",
    "zh": "Z1负载限制异常，请联系售后处理"
  },
  "dock_tip_0x30900023": {
    "en": "The machine nest is in emergency stop. Reset the hardware emergency stop button before operating the equipment.",
    "zh": "机巢急停中，请复位硬件急停按钮后再操作设备"
  },
  "dock_tip_0x30900024": {
    "en": "Combined instruction status abnormality.Contact after-sales service for assistance.",
    "zh": "组合指令状态异常，请联系售后处理"
  },
  "dock_tip_0x30900025": {
    "en": "Machine nest motion timeout.Contact after-sales service for assistance.",
    "zh": "机巢运动超时，请联系售后处理"
  },
  "dock_tip_0x30900026": {
    "en": "Hatch door abnormality.Contact after-sales service for assistance.",
    "zh": "舱门异常，请联系售后处理"
  },
  "dock_tip_0x30900027": {
    "en": "Battery abnormality.Contact after-sales service for assistance.",
    "zh": "电池异常，请联系售后处理"
  },
  "dock_tip_0x30900028": {
    "en": "Battery 1 empty slot insertion/removal abnormality.Contact after-sales service for assistance.",
    "zh": "电池1空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900029": {
    "en": "Battery 2 empty slot insertion/removal abnormality. Contact after-sales service for assistance.",
    "zh": "电池2空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900030": {
    "en": "Battery 3 empty slot insertion/removal abnormality.Contact after-sales service for assistance.",
    "zh": "电池3空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900031": {
    "en": "Battery 4 empty slot insertion/removal abnormality.Contact after-sales service for assistance.",
    "zh": "电池4空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900032": {
    "en": "Battery 5 empty slot insertion/removal abnormality.Contact after-sales service for assistance.",
    "zh": "电池5空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900033": {
    "en": "Battery 6 empty slot insertion/removal abnormality.Contact after-sales service for assistance.",
    "zh": "电池6空槽拔插异常，请联系售后处理"
  },
  "dock_tip_0x30900034": {
    "en": "Battery 1 Cycle Count Error. Please contact customer support.",
    "zh": "电池1循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900035": {
    "en": "Battery 2 Cycle Count Error. Please contact customer support.",
    "zh": "电池2循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900036": {
    "en": "Battery 3 Cycle Count Error. Please contact customer support.",
    "zh": "电池3循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900037": {
    "en": "Battery 4 Cycle Count Error. Please contact customer support.",
    "zh": "电池4循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900038": {
    "en": "Battery 5 Cycle Count Error. Please contact customer support.",
    "zh": "电池5循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900039": {
    "en": "Battery 6 Cycle Count Error. Please contact customer support.",
    "zh": "电池6循环次数异常，请联系售后处理"
  },
  "dock_tip_0x30900100": {
    "en": "The aircraft's attitude deviation from the machine nest is too large, and retrieval has been paused.",
    "zh": "飞机姿态与机巢偏差过大，已暂停回收"
  },
  "dock_tip_0x3100": {
    "en": "Wireless charging communication timeout protection",
    "zh": "无线充通信超时保护"
  },
  "dock_tip_0x40001001": {
    "en": "Wind speed near Nest exceeds threshold. Flight prohibited.",
    "zh": "机巢附近风速超出阈值，禁止飞行"
  },
  "dock_tip_0x40001001_in_the_sky": {
    "en": "Wind speed near Nest exceeds threshold. Fly with caution.",
    "zh": "机巢附近风速超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001002": {
    "en": "Temperature outside Nest exceeds threshold. Flight prohibited.",
    "zh": "机巢外温度超出阈值，禁止飞行"
  },
  "dock_tip_0x40001002_in_the_sky": {
    "en": "Temperature outside Nest exceeds threshold. Fly with caution.",
    "zh": "机巢外温度超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001003": {
    "en": "Temperature outside Nest exceeds threshold. Flight prohibited.",
    "zh": "机巢外温度超出阈值，禁止飞行"
  },
  "dock_tip_0x40001003_in_the_sky": {
    "en": "Temperature outside Nest exceeds threshold. Fly with caution.",
    "zh": "机巢外温度超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001004": {
    "en": "Rainfall near Nest exceeds threshold. Flight prohibited.",
    "zh": "机巢附近雨量超出阈值，禁止飞行"
  },
  "dock_tip_0x40001004_in_the_sky": {
    "en": "Rainfall near Nest exceeds threshold. Fly with caution.",
    "zh": "机巢附近雨量超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001006": {
    "en": "Forecast wind speed exceeds threshold. Flight prohibited.",
    "zh": "气象预报风速超出阈值，禁止飞行"
  },
  "dock_tip_0x40001006_in_the_sky": {
    "en": "Forecast wind speed exceeds threshold. Fly with caution.",
    "zh": "气象预报风速超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001007": {
    "en": "Forecast temperature exceeds threshold. Flight prohibited.",
    "zh": "气象预报温度超出阈值，禁止飞行"
  },
  "dock_tip_0x40001007_in_the_sky": {
    "en": "Forecast temperature exceeds threshold. Fly with caution.",
    "zh": "气象预报温度超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001008": {
    "en": "Forecast temperature exceeds threshold. Flight prohibited.",
    "zh": "气象预报温度超出阈值，禁止飞行"
  },
  "dock_tip_0x40001008_in_the_sky": {
    "en": "Forecast temperature exceeds threshold. Fly with caution.",
    "zh": "气象预报温度超出阈值，请注意飞行安全"
  },
  "dock_tip_0x40001009": {
    "en": "Forecast rainfall exceeds threshold. Flight prohibited.",
    "zh": "气象预报雨量超出阈值，禁止飞行"
  },
  "dock_tip_0x40001009_in_the_sky": {
    "en": "Forecast rainfall exceeds threshold. Fly with caution.",
    "zh": "气象预报雨量超出阈值，请注意飞行安全"
  },
  "dock_tip_0x4001": {
    "en": "Overtemperature of charging",
    "zh": "充电过温"
  },
  "dock_tip_0x4002": {
    "en": "Low temperature of charging",
    "zh": "充电欠温"
  },
  "dock_tip_0x4003": {
    "en": "Overcurr t of charging",
    "zh": "充电过流"
  },
  "dock_tip_0x4004": {
    "en": "Abnormal of drone charging",
    "zh": "无人机充电异常"
  },
  "dock_tip_0x4005": {
    "en": "Charging board high temperature",
    "zh": "充电板高温"
  },
  "dock_tip_0x4006": {
    "en": "Charging board low temperature",
    "zh": "充电板低温"
  },
  "dock_tip_0x4007": {
    "en": "Charging board high temperature 2",
    "zh": "充电板高温 2"
  },
  "dock_tip_0x4020": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4021": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4022": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4023": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4031": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4032": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4033": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4034": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4035": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4036": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x4037": {
    "en": "Power adapter error. Please check that the power supply is functioning properly. If the error persists despite normal power supply, please contact after-sales support.",
    "zh": "电源适配器异常，请检查供电是否正常；若供电正常仍报错，请联系售后支持"
  },
  "dock_tip_0x5001": {
    "en": "Abnormal of U-disk reading and writing",
    "zh": "U盘读写异常"
  },
  "dock_tip_0x5002": {
    "en": "Abnormal of WIFI startup",
    "zh": "WIFI启动异常"
  },
  "dock_tip_0x5003": {
    "en": "Abnormal communicate of RTK",
    "zh": "RTK通信异常"
  },
  "dock_tip_0x5004": {
    "en": "Abnormal communicate of power board",
    "zh": "电源板通信异常"
  },
  "dock_tip_0x5005": {
    "en": "Abnormal of 1000M network card",
    "zh": "千兆网卡异常"
  },
  "dock_tip_0x5006": {
    "en": "Abnormal of 100M network card",
    "zh": "百兆网卡异常"
  },
  "dock_tip_0x5007": {
    "en": "Abnormal of monitor camera (connected to 100M network card)",
    "zh": "监控摄像头异常(接百兆网卡)"
  },
  "dock_tip_0x5009": {
    "en": "Overtemperature of system",
    "zh": "系统温度过高"
  },
  "dock_tip_0x5012": {
    "en": "Overuse of system storage space",
    "zh": "系统存储空间使用过高"
  },
  "dock_tip_0x5014": {
    "en": "Abnormal of network",
    "zh": "网络异常"
  },
  "dock_tip_0x5015": {
    "en": "Interfer ce of radio frequ cy",
    "zh": "射频干扰"
  },
  "dock_tip_0x6001": {
    "en": "Abnormal of video codec",
    "zh": "视频编解码异常"
  },
  "dock_tip_0x6002": {
    "en": "Failed downloading file from camera",
    "zh": "从相机下载文件失败"
  },
  "dock_tip_0x6003": {
    "en": "Failed to upload files to command c ter",
    "zh": "上传文件到指挥中心失败"
  },
  "dock_tip_0x6004": {
    "en": "Abnormal login of camera outside the nest",
    "zh": "巢外摄像头登录异常"
  },
  "fpv_tip_0x0001": {
    "en": "Aircraft attitude abnormal, please land as soon as possible",
    "zh": "飞机姿态异常，请尽快降落"
  },
  "fpv_tip_0x0002": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0003": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0004": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0005": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0006": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0007": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0008": {
    "en": "Flight control abnormal, please land as soon as possible",
    "zh": "飞行控制异常，请尽快降落"
  },
  "fpv_tip_0x0101": {
    "en": "Battery voltage abnormal, please return or land as soon as possible",
    "zh": "电池电压异常，请尽快返航或降落"
  },
  "fpv_tip_0x0102": {
    "en": "Battery abnormal, please check or replace the battery",
    "zh": "电池异常，请检查或更换电池"
  },
  "fpv_tip_0x0103": {
    "en": "Battery abnormal, please check or replace the battery",
    "zh": "电池异常，请检查或更换电池"
  },
  "fpv_tip_0x0105": {
    "en": "The battery temperature is too low. Wait until self-heating is completed.",
    "zh": "电池温度过低，请稍等待预热成功"
  },
  "fpv_tip_0x0105_in_the_sky": {
    "en": "Battery temperature is too low. Return or land immediately.",
    "zh": "电池温度过低，请尽快返航或降落"
  },
  "fpv_tip_0x0106": {
    "en": "Left battery temperature too high, please cool down before use.",
    "zh": "电池温度过高，请降温后使用"
  },
  "fpv_tip_0x0106_in_the_sky": {
    "en": "Left battery temperature too high, please return or land as soon as possible.",
    "zh": "电池温度过高，请尽快返航或降落"
  },
  "fpv_tip_0x0107": {
    "en": "The aircraft battery is critically low",
    "zh": "飞机电量严重低"
  },
  "fpv_tip_0x0108": {
    "en": "Aircraft battery is low",
    "zh": "飞机电量低"
  },
  "fpv_tip_0x0109": {
    "en": "The aircraft battery is low, only enough for return to home.",
    "zh": "飞机电量低，仅够飞回返航点"
  },
  "fpv_tip_0x010A": {
    "en": "Battery voltage difference too large, please replace the battery",
    "zh": "电池压差过大，请更换电池"
  },
  "fpv_tip_0x010B": {
    "en": "Battery over-discharged, please replace the battery",
    "zh": "电池过放，请更换电池"
  },
  "fpv_tip_0x010C": {
    "en": "Battery voltage not updating, please return immediately and restart the aircraft",
    "zh": "电池电压不更新，请尽快返航并重启飞机"
  },
  "fpv_tip_0x010D": {
    "en": "Battery cell voltage low. Flight speed limited. Check or replace the battery.",
    "zh": "电池电芯电压低，飞行速度受限，请检查或更换电池"
  },
  "fpv_tip_0x010E": {
    "en": "Overloaded, please check the payload",
    "zh": "负载过重，请检查负载"
  },
  "fpv_tip_0x010F": {
    "en": "High power consumption detected. Reducing speed or altitude for protection. Reduce payload and avoid low battery.",
    "zh": "飞机飞行功率过大，正在自动降速或降高保护，请减轻负载且避免电量过低"
  },
  "fpv_tip_0x0110": {
    "en": "Battery temperature too high, please cool down before use",
    "zh": "电池温度过高，请降温后使用"
  },
  "fpv_tip_0x0111": {
    "en": "Battery temperature too high, please cool down before use",
    "zh": "电池温度过高，请降温后使用"
  },
  "fpv_tip_0x0112": {
    "en": "Battery cycle count too high, please replace the battery",
    "zh": "电池循环次数过多，请更换电池"
  },
  "fpv_tip_0x0113": {
    "en": "Battery cycle count too high, please replace the battery",
    "zh": "电池循环次数过多，请更换电池"
  },
  "fpv_tip_0x0118": {
    "en": "Battery temperature too low, please wait for preheating to complete",
    "zh": "电池温度过低，请稍等待预热成功"
  },
  "fpv_tip_0x0119": {
    "en": "Battery temperature too low, please wait for preheating to complete",
    "zh": "电池温度过低，请稍等待预热成功"
  },
  "fpv_tip_0x011A": {
    "en": "Battery temperature low, flight speed limited",
    "zh": "电池温度偏低，飞行速度受限"
  },
  "fpv_tip_0x011B": {
    "en": "Battery temperature low, flight speed limited",
    "zh": "电池温度偏低，飞行速度受限"
  },
  "fpv_tip_0x011C": {
    "en": "Battery temperature and voltage low, please replace the battery",
    "zh": "电池低温低电，请更换电池"
  },
  "fpv_tip_0x011D": {
    "en": "Battery temperature and voltage low, please replace the battery",
    "zh": "电池低温低电，请更换电池"
  },
  "fpv_tip_0x0120": {
    "en": "Critical low battery. Land as soon as possible and fly with caution",
    "zh": "飞机严重低电量，请尽快降落，注意飞行安全"
  },
  "fpv_tip_0x0121": {
    "en": "Low battery. Return to home immediately",
    "zh": "飞机电量低，请尽快返航"
  },
  "fpv_tip_0x0122": {
    "en": "",
    "zh": ""
  },
  "fpv_tip_0x0122_in_the_sky": {
    "en": "Low aircraft battery. Returnt to home as soon as possible",
    "zh": "飞机电量低，请尽快返航"
  },
  "fpv_tip_0x0129": {
    "en": "Arms not fully deployed. Please fully extend the arms or use the one-click takeoff feature.",
    "zh": "机臂未展开到位，请完全展开机臂或使用一键起飞功能"
  },
  "fpv_tip_0x012A": {
    "en": "Satellite positioning is experiencing abnormal signal interference. Fly with caution.",
    "zh": "卫星定位受异常信号干扰，请谨慎飞行。"
  },
  "fpv_tip_0x012A_in_the_sky": {
    "en": "Satellite positioning is experiencing abnormal signal interference. It is recommended to return to home or land immediately.",
    "zh": "卫星定位受异常信号干扰，建议立即返航或降落。"
  },
  "fpv_tip_0x0201": {
    "en": "Partial propeller blades stopped rotating, please land as soon as possible",
    "zh": "部分桨叶停转，请尽快降落"
  },
  "fpv_tip_0x0203": {
    "en": "ESC abnormal. Restart the aircraft",
    "zh": "电调异常，请重启飞机"
  },
  "fpv_tip_0x0203_in_the_sky": {
    "en": "ESC abnormal. Execute RTH or land immediately.",
    "zh": "电调异常，请尽快返航或降落"
  },
  "fpv_tip_0x0204": {
    "en": "Please confirm if the propeller blades are installed correctly",
    "zh": "请确认桨页是否安装正常"
  },
  "fpv_tip_0x0207": {
    "en": "Propeller blade not installed, please confirm if the propeller blades are installed correctly",
    "zh": "桨叶未安装，请确认桨页是否安装正常"
  },
  "fpv_tip_0x0208": {
    "en": "Motor stall, propellers have stopped. Do not bring the aircraft propellers near obstacles",
    "zh": "电机堵转，已停桨，请勿将飞机桨叶靠近障碍物"
  },
  "fpv_tip_0x0208_in_the_sky": {
    "en": "Motor stall, propellers have stopped. Land immediately",
    "zh": "电机堵转，已停桨，请立即降落"
  },
  "fpv_tip_0x0209": {
    "en": "ESC not ready. Take off later",
    "zh": "电调未就绪，请稍后起飞"
  },
  "fpv_tip_0x0209_in_the_sky": {
    "en": "ESC not ready. Execute RTH or land immediately.",
    "zh": "电调未就绪，请尽快返航或降落"
  },
  "fpv_tip_0x0301": {
    "en": "IMU abnormal, takeoff prohibited",
    "zh": "IMU异常，禁止起飞"
  },
  "fpv_tip_0x0302": {
    "en": "Barometer abnormal, takeoff prohibited",
    "zh": "气压计异常，禁止起飞"
  },
  "fpv_tip_0x0303": {
    "en": "Compass abnormal, please be cautious",
    "zh": "指南针异常，请注意安全"
  },
  "fpv_tip_0x0305": {
    "en": "IMU abnormal, please calibrate IMU",
    "zh": "IMU异常，请校准IMU"
  },
  "fpv_tip_0x0306": {
    "en": "Compass abnormal, please calibrate compass",
    "zh": "指南针异常，请校准指南针"
  },
  "fpv_tip_0x0307": {
    "en": "RTK not ready, please wait for takeoff",
    "zh": "RTK未就绪，请稍后起飞"
  },
  "fpv_tip_0x0308": {
    "en": "Gimbal not ready, please wait for takeoff",
    "zh": "云台未就绪，请稍后起飞"
  },
  "fpv_tip_0x030B": {
    "en": "Motor temperature too high, flight speed reduced, please return or land as soon as possible",
    "zh": "电机温度过高，已降低飞行速度，请尽快返航或降落"
  },
  "fpv_tip_0x030D": {
    "en": "Aircraft was not restarted after compass calibration. Takeoff is prohibited",
    "zh": "指南针校准后未重启飞机，禁止起飞"
  },
  "fpv_tip_0x030D_in_the_sky": {
    "en": "Aircraft not restarted after compass calibration. Execute RTH or land immediately.",
    "zh": "指南针校准后未重启飞机，请尽快返航或降落"
  },
  "fpv_tip_0x030E": {
    "en": "Aircraft was not restarted after IMU calibration. Takeoff is prohibited",
    "zh": "IMU校准后未重启飞机，禁止起飞"
  },
  "fpv_tip_0x030E_in_the_sky": {
    "en": "Aircraft not restarted after IMU calibration. Execute RTH or land immediately.",
    "zh": "IMU校准后未重启飞机，请尽快返航或降落"
  },
  "fpv_tip_0x0401": {
    "en": "Aircraft tilt too large, please place on flat ground",
    "zh": "飞机倾角过大，请放置在平坦地面"
  },
  "fpv_tip_0x0402": {
    "en": "Aircraft disconnected",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0404": {
    "en": "Currently in a no-fly zone, takeoff prohibited",
    "zh": "当前位于禁飞区，禁止起飞"
  },
  "fpv_tip_0x0405": {
    "en": "Maximum altitude reached",
    "zh": "已到达限高高度"
  },
  "fpv_tip_0x0406": {
    "en": "Maximum distance reached",
    "zh": "飞机已到达设置最远距离"
  },
  "fpv_tip_0x0407": {
    "en": "Maximum altitude reached",
    "zh": "飞机已到达设置最高高度"
  },
  "fpv_tip_0x0408": {
    "en": "Upgrading, please wait",
    "zh": "升级中，请稍候"
  },
  "fpv_tip_0x0409": {
    "en": "Aircraft attitude initializing",
    "zh": "飞机姿态初始化中"
  },
  "fpv_tip_0x040A": {
    "en": "UOM not registered",
    "zh": "UOM未登记"
  },
  "fpv_tip_0x040B": {
    "en": "High wind speed, aircraft unstable, please be cautious",
    "zh": "风速过高飞机无法稳定飞行，请注意安全"
  },
  "fpv_tip_0x040C": {
    "en": "Weak GNSS signal, return point may have deviation",
    "zh": "GNSS信号弱返航点可能存在偏差"
  },
  "fpv_tip_0x040D": {
    "en": "Weak GNSS signal, please stay away from building clusters",
    "zh": "GNSS信号弱请远离建筑群"
  },
  "fpv_tip_0x040E": {
    "en": "Aircraft susceptible to GNSS spoofing, attempting to return",
    "zh": "飞机遭受GNSS诱骗，开始尝试返航"
  },
  "fpv_tip_0x040F": {
    "en": "Battery not installed properly, please check",
    "zh": "电池未安装到位，请检查"
  },
  "fpv_tip_0x0410": {
    "en": "Left front arm not unfolded properly, please check",
    "zh": "左前机臂未展开到位，请检查"
  },
  "fpv_tip_0x0411": {
    "en": "Right front arm not unfolded properly, please check",
    "zh": "右前机臂未展开到位，请检查"
  },
  "fpv_tip_0x0412": {
    "en": "Left rear arm not unfolded properly, please check",
    "zh": "左后机臂未展开到位，请检查"
  },
  "fpv_tip_0x0413": {
    "en": "Right rear arm not unfolded properly, please check",
    "zh": "右后机臂未展开到位，请检查"
  },
  "fpv_tip_0x0418": {
    "en": "Battery not activated, please check",
    "zh": "电池未生效，请检查"
  },
  "fpv_tip_0x0419": {
    "en": "Battery data abnormal, please check",
    "zh": "电池数据异常，请检查"
  },
  "fpv_tip_0x041A": {
    "en": "Battery voltage difference too large, please check",
    "zh": "电池电量差异过大，请检查"
  },
  "fpv_tip_0x041B": {
    "en": "Remote ID information not filled, takeoff prohibited",
    "zh": "未填写Remote ID信息，禁止起飞"
  },
  "fpv_tip_0x041C": {
    "en": "Partial propeller blades stopped rotating, please land as soon as possible",
    "zh": "部分桨叶停转，请尽快降落"
  },
  "fpv_tip_0x041D": {
    "en": "Flight mission abnormal, please restart the aircraft",
    "zh": "任务管理模块未就绪，请稍后起飞"
  },
  "fpv_tip_0x041D_in_the_sky": {
    "en": "Flight mission abnormal, aircraft initiating return.",
    "zh": "任务管理模块异常，飞机开始返航"
  },
  "fpv_tip_0x041E": {
    "en": "UOM not registered, takeoff prohibited",
    "zh": "UOM未注册，禁止起飞"
  },
  "fpv_tip_0x041F": {
    "en": "Aircraft experiencing abnormal vibration, please contact customer service, hotline: 400 800 1866",
    "zh": "飞机异常震动，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0420": {
    "en": "Rainfall too heavy. Takeoff is prohibited.",
    "zh": "雨量过大，禁止起飞"
  },
  "fpv_tip_0x0420_in_the_sky": {
    "en": "Rainfall too heavy. Aircraft is landing. Use controls to avoid obstacles.",
    "zh": "雨量过大，飞机开始降落，您可打杆躲避障碍物"
  },
  "fpv_tip_0x0422": {
    "en": "Spoofed drone signal detected nearby. Fly with caution",
    "zh": "附近检测到诱骗无人机信号，请谨慎飞行。"
  },
  "fpv_tip_0x0422_in_the_sky": {
    "en": "Spoofed drone signal detected nearby. Fly with caution",
    "zh": "附近检测到诱骗无人机信号，请谨慎飞行。"
  },
  "fpv_tip_0x0451": {
    "en": "Unstable RTK signal, please be cautious",
    "zh": "RTK信号不稳定，请注意安全"
  },
  "fpv_tip_0x0501": {
    "en": "Remote controller not connected to aircraft",
    "zh": "遥控器与飞机未连接"
  },
  "fpv_tip_0x0502": {
    "en": "Remote controller not connected to aircraft",
    "zh": "遥控器与飞机未连接"
  },
  "fpv_tip_0x0503": {
    "en": "Low aircraft battery, initiating automatic return",
    "zh": "飞机电池电量低，开始自动返航"
  },
  "fpv_tip_0x0504": {
    "en": "Flying towards alternate landing point",
    "zh": "正在飞向备降点"
  },
  "fpv_tip_0x0505": {
    "en": "Aircraft initiating return",
    "zh": "飞机开始返航"
  },
  "fpv_tip_0x0506": {
    "en": "Aircraft initiating return",
    "zh": "飞机开始返航"
  },
  "fpv_tip_0x0507": {
    "en": "Aircraft initiating return",
    "zh": "飞机开始返航"
  },
  "fpv_tip_0x0508": {
    "en": "Aircraft initiating return",
    "zh": "飞机开始返航"
  },
  "fpv_tip_0x0509": {
    "en": "Aircraft initiating return",
    "zh": "飞机开始返航"
  },
  "fpv_tip_0x050A": {
    "en": "Aircraft approaching no-fly zone",
    "zh": "飞机靠近禁飞区"
  },
  "fpv_tip_0x050B": {
    "en": "Mission completed, initiating return",
    "zh": "任务已完成，开始返航"
  },
  "fpv_tip_0x0519": {
    "en": "No GNSS and visual positioning, please be cautious",
    "zh": "无GNSS和视觉定位，请注意安全"
  },
  "fpv_tip_0x051C": {
    "en": "No GPS signal, exiting mission",
    "zh": "无GPS信号，退出任务"
  },
  "fpv_tip_0x051D": {
    "en": "Mission upload failed, please retry",
    "zh": "任务上传失败，请重新上传"
  },
  "fpv_tip_0x051E": {
    "en": "Mission execution failed, please try again later",
    "zh": "任务执行失败，请稍后执行"
  },
  "fpv_tip_0x051F": {
    "en": "Mission execution failed, please try again later",
    "zh": "任务执行失败，请稍后执行"
  },
  "fpv_tip_0x0520": {
    "en": "Mission execution failed, please try again later",
    "zh": "任务执行失败，请稍后执行"
  },
  "fpv_tip_0x0521": {
    "en": "Mission upload failed, please retry",
    "zh": "任务上传失败，请重新上传"
  },
  "fpv_tip_0x0534": {
    "en": "Currently in a no-fly aone. The aircraft is beginning to land. Exercise caution.",
    "zh": "当前位于禁飞区，飞机开始降落，请注意安全"
  },
  "fpv_tip_0x0540": {
    "en": "Mission upload failed, please retry",
    "zh": "任务上传失败，请重新上传"
  },
  "fpv_tip_0x0541": {
    "en": "Mission upload failed, please retry",
    "zh": "任务上传失败，请重新上传"
  },
  "fpv_tip_0x0542": {
    "en": "Mission upload failed, please retry",
    "zh": "任务上传失败，请重新上传"
  },
  "fpv_tip_0x0543": {
    "en": "Flight path passes through no-fly zone, unable to execute mission",
    "zh": "航线经过禁飞区，无法执行任务"
  },
  "fpv_tip_0x0544": {
    "en": "Waypoints exceed maximum flight distance or altitude, please adjust waypoint settings",
    "zh": "航点超出最大飞行距离或限高高度，请调整航点设置"
  },
  "fpv_tip_0x0545": {
    "en": "Flight path exceeds aircraft's maximum flight distance, please adjust flight path",
    "zh": "航线超出飞机最大飞行距离，请调整航线"
  },
  "fpv_tip_0x0546": {
    "en": "Too far from mission area, unable to execute",
    "zh": "距离任务区域过远，无法执行"
  },
  "fpv_tip_0x0547": {
    "en": "Mission duration exceeds maximum flight time, please adjust flight path",
    "zh": "任务时长超出最大航时，请调整航线"
  },
  "fpv_tip_0x0548": {
    "en": "Aircraft not responding, please try restarting",
    "zh": "飞机未响应，请重启后再试"
  },
  "fpv_tip_0x0601": {
    "en": "Gimbal stuck error. Check if the gimbal is stuck.",
    "zh": "云台堵转，请检查云台是否卡住"
  },
  "fpv_tip_0x0602": {
    "en": "Gimbal IMU sensor is not calibrated. Please calibrate.",
    "zh": "云台IMU传感器未校准，请校准"
  },
  "fpv_tip_0x0604": {
    "en": "Gimbal overheated, please check gimbal",
    "zh": "云台过热，请检查云台"
  },
  "fpv_tip_0x0605": {
    "en": "Gimbal communication with flight controller interrupted",
    "zh": "云台与飞控通信中断"
  },
  "fpv_tip_0x0606": {
    "en": "Gimbal calibration failed. Check the gimbal and restart the aircraft.",
    "zh": "云台自检失败，请检查云台并重启飞机"
  },
  "fpv_tip_0x0608": {
    "en": "Gimbal reached the mechanical limit. Check the gimbal or calibrate compass.",
    "zh": "云台达到限位"
  },
  "fpv_tip_0x0701": {
    "en": "Left and right obstacle avoidance failed, please be cautious",
    "zh": "左右避障失效，请注意安全"
  },
  "fpv_tip_0x0702": {
    "en": "Left and right obstacle avoidance and SLAM failed, please be cautious",
    "zh": "左右避障和slam失效，请注意安全"
  },
  "fpv_tip_0x0704": {
    "en": "Left and right obstacle avoidance failed, please be cautious",
    "zh": "左右避障失效，请注意安全"
  },
  "fpv_tip_0x0705": {
    "en": "Left and right obstacle avoidance failed, please be cautious",
    "zh": "左右避障失效，请注意安全"
  },
  "fpv_tip_0x0706": {
    "en": "Left and right obstacle avoidance failed, please be cautious",
    "zh": "左右避障失效，请注意安全"
  },
  "fpv_tip_0x0707": {
    "en": "SLAM disabled, please be cautious",
    "zh": "slam关闭，请注意安全"
  },
  "fpv_tip_0x0708": {
    "en": "Obstacle avoidance ineffective in low light conditions, please be cautious",
    "zh": "环境光线暗，左右避障失效，请注意安全"
  },
  "fpv_tip_0x0709": {
    "en": "Visual perception affected in rainy or foggy conditions, please temporarily disable obstacle avoidance and be cautious",
    "zh": "雨雾环境视觉感知受影响，请暂时关闭避障并注意安全"
  },
  "fpv_tip_0x070A": {
    "en": "Front camera lens dirty, please be cautious and clean the lens",
    "zh": "前视镜头有脏污，请注意安全并清洁镜头"
  },
  "fpv_tip_0x070B": {
    "en": "Rear camera lens dirty, please be cautious and clean the lens",
    "zh": "后视镜头有脏污，请注意安全并清洁镜头"
  },
  "fpv_tip_0x070C": {
    "en": "Upper camera lens dirty, please be cautious and clean the lens",
    "zh": "上视镜头有脏污，请注意安全并清洁镜头"
  },
  "fpv_tip_0x070D": {
    "en": "Lower camera lens dirty, please be cautious and clean the lens",
    "zh": "下视镜头有脏污，请注意安全并清洁镜头"
  },
  "fpv_tip_0x078F": {
    "en": "Entering low-power mode, infrared lens deactivated",
    "zh": "进入低功耗模式，红外镜头已关闭"
  },
  "fpv_tip_0x0801": {
    "en": "SD card error, please replace SD card",
    "zh": "SD卡错误，请更换SD卡"
  },
  "fpv_tip_0x0802": {
    "en": "SD card full, switching to onboard flash memory",
    "zh": "SD卡已满，将切换到机载闪存"
  },
  "fpv_tip_0x0803": {
    "en": "Onboard flash memory full, switching to SD card",
    "zh": "机载闪存已满，将切换到SD卡"
  },
  "fpv_tip_0x0804": {
    "en": "Wide-angle lens abnormal",
    "zh": "广角镜头异常"
  },
  "fpv_tip_0x0805": {
    "en": "Telephoto lens abnormal",
    "zh": "长焦镜头异常"
  },
  "fpv_tip_0x0806": {
    "en": "Upper and lower vision obstacle avoidance abnormal",
    "zh": "上下视觉避障异常"
  },
  "fpv_tip_0x0807": {
    "en": "Front and rear vision obstacle avoidance abnormal",
    "zh": "前后视觉避障异常"
  },
  "fpv_tip_0x0808": {
    "en": "Zoom function abnormal",
    "zh": "变焦功能异常"
  },
  "fpv_tip_0x0809": {
    "en": "Telephoto lens abnormal",
    "zh": "长焦镜头异常"
  },
  "fpv_tip_0x080B": {
    "en": "F401 firmware upgrade failed",
    "zh": "F401 固件升级失败"
  },
  "fpv_tip_0x080F": {
    "en": "Entering low-power mode, infrared lens deactivated",
    "zh": "进入低功耗模式，红外镜头已关闭"
  },
  "fpv_tip_0x080a": {
    "en": "Focus failed, please check if the lens is normal",
    "zh": "对焦失败，请检查镜头是否正常"
  },
  "fpv_tip_0x080c": {
    "en": "Please check gimbal",
    "zh": "请检查云台"
  },
  "fpv_tip_0x080e": {
    "en": "TF card write slow, please format TF card or replace with high-speed card",
    "zh": "TF卡写入慢，请格式化TF卡或更换高速卡"
  },
  "fpv_tip_0x0820": {
    "en": "Image transmission abnormal, please be cautious during flight",
    "zh": "图像传输异常，请注意飞行安全"
  },
  "fpv_tip_0x0821": {
    "en": "Image transmission abnormal, please restart the aircraft or reinstall the gimbal",
    "zh": "图像传输异常，请重启飞机或重装云台"
  },
  "fpv_tip_0x0824": {
    "en": "Image transmission abnormal, please be cautious during flight",
    "zh": "图像传输异常，请注意飞行安全"
  },
  "fpv_tip_0x0862": {
    "en": "Enter low power mode, gimbal camera has been turned off",
    "zh": "进入低功耗模式，云台相机已关闭"
  },
  "fpv_tip_0x0901": {
    "en": "Radar temperature too high",
    "zh": "雷达温度过高"
  },
  "fpv_tip_0x0902": {
    "en": "Radar self-check failed, please try restarting the aircraft to fix",
    "zh": "雷达自检失败，请尝试重启飞机修复"
  },
  "fpv_tip_0x0903": {
    "en": "Radar abnormal, please try restarting the aircraft to fix",
    "zh": "雷达异常，请尝试重启飞机修复"
  },
  "fpv_tip_0x0904": {
    "en": "Radar data acquisition abnormal, please try restarting the aircraft to fix",
    "zh": "雷达采数异常，请尝试重启飞机修复"
  },
  "fpv_tip_0x0905": {
    "en": "Radar abnormal, please try restarting the aircraft to fix",
    "zh": "雷达异常，请尝试重启飞机修复"
  },
  "fpv_tip_0x0906": {
    "en": "PPS signal abnormal",
    "zh": "PPS信号异常"
  },
  "fpv_tip_0x0907": {
    "en": "Radar not calibrated, please calibrate radar",
    "zh": "雷达未标定，请进行标定"
  },
  "fpv_tip_0x0A81": {
    "en": "Aircraft signal interfered",
    "zh": "飞机信号受到干扰"
  },
  "fpv_tip_0x0A82": {
    "en": "Image transmission version mismatch, affecting control and image quality. Upgrade immediately",
    "zh": "图传版本不匹配，影响飞行操控与画质，请立即升级"
  },
  "fpv_tip_0x0A83": {
    "en": "Aircraft antenna signal is imbalanced. Fly with caution, and check the antenna or contact after-sales support.",
    "zh": "飞机天线信号不均衡，请注意飞行安全，并检查天线或联系售后处理"
  },
  "fpv_tip_0x0A84": {
    "en": "Remote controller antenna signal is imbalanced. Fly with caution, and check the antenna or contact after-sales support.",
    "zh": "天线信号不均衡，请注意飞行安全，并检查天线或联系售后处理"
  },
  "fpv_tip_0x0A85": {
    "en": "Video transmission signal is weak.",
    "zh": "飞机图传信号弱"
  },
  "fpv_tip_0x0A86": {
    "en": "Video transmission signal is lost.",
    "zh": "飞机图传信号丢失"
  },
  "fpv_tip_0x0B06": {
    "en": "Flight mission abnormal, please retry or restart the aircraft",
    "zh": "飞行任务异常，请重新尝试或重启飞行器"
  },
  "fpv_tip_0x0B07": {
    "en": "Flight mission abnormal, please retry or restart the aircraft",
    "zh": "飞行任务异常，请重新尝试或重启飞行器"
  },
  "fpv_tip_0x0B08": {
    "en": "Visual positioning disabled, please be cautious",
    "zh": "视觉定位关闭，请注意安全"
  },
  "fpv_tip_0x0B09": {
    "en": "System abnormal restart, please contact customer service, hotline: 400 800 1866",
    "zh": "系统异常重启，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0B0A": {
    "en": "System temperature too high, please contact customer service, hotline: 400 800 1866",
    "zh": "系统温度过高，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0B0B": {
    "en": "System CPU load too high, please contact customer service, hotline: 400 800 1866",
    "zh": "系统CPU负载过高，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0B0C": {
    "en": "System memory usage too high, please contact customer service, hotline: 400 800 1866",
    "zh": "系统内存占用过高，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0B0D": {
    "en": "System storage space usage too high, please contact customer service, hotline: 400 800 1866",
    "zh": "系统存储空间使用过高，请联系售后处理，服务热线  400 800 1866"
  },
  "fpv_tip_0x0D04": {
    "en": "Waypoint in no-fly zone",
    "zh": "标记点位置处于禁飞区"
  },
  "fpv_tip_0x0D05": {
    "en": "Laser module malfunction, use estimated distance",
    "zh": "激光模块失效，使用估计距离"
  },
  "fpv_tip_0x0D07": {
    "en": "Obstacle avoidance system failed, please be cautious",
    "zh": "避障系统失效，请注意安全"
  },
  "fpv_tip_0x0D08": {
    "en": "Obstacle avoidance system abnormal, please temporarily disable and be cautious",
    "zh": "避障系统异常，请临时关闭并注意安全"
  },
  "fpv_tip_0x0D09": {
    "en": "Obstacle avoidance ineffective in low light conditions, please be cautious",
    "zh": "暗光环境避障无效，请注意安全"
  },
  "fpv_tip_0x0D16": {
    "en": "No-fly zone limitation triggered. The automated mission will be aborted. Please manually fly out of the no-fly zone.",
    "zh": "触发禁飞区限制，将退出自动任务，请手动飞离禁飞区"
  },
  "fpv_tip_0x0D18": {
    "en": "Aircraft entering warning zone",
    "zh": "飞机进入警示区"
  },
  "fpv_tip_0x0D19": {
    "en": "Aircraft entering enhanced warning zone",
    "zh": "飞机进入增强警示区"
  },
  "fpv_tip_0x0D25": {
    "en": "Mission file decompression failed, please retry upload",
    "zh": "任务文件解压失败，请重新上传"
  },
  "fpv_tip_0x0D26": {
    "en": "Mission gimbal angle not supported, please check gimbal settings",
    "zh": "任务云台角度不支持，请检查云台设置"
  },
  "fpv_tip_0x0D27": {
    "en": "Mission failed, aircraft initiating return, please adjust starting point of flight path",
    "zh": "任务失败，飞机开始返航，请调整航线起点位置"
  },
  "fpv_tip_0x0D28": {
    "en": "Aircraft taking photos prematurely, please adjust waypoint positions",
    "zh": "飞机提前拍照，请调整航点位置"
  },
  "fpv_tip_0x0D2C": {
    "en": "Aircraft approaching custom no-fly zone",
    "zh": "无人机靠近自定义限飞区"
  },
  "fpv_tip_0x0D2D": {
    "en": "Aircraft outside custom operation zone. Takeoff prohibited",
    "zh": "无人机位于自定义作业区外，禁止起飞"
  },
  "fpv_tip_0x0D2E": {
    "en": "Aircraft out of custom operation zone. Return or land immediately",
    "zh": "无人机越出自定义作业区，请立即返航或降落"
  },
  "fpv_tip_0x0D2F": {
    "en": "Aircraft out of custom operation zone. Return or land immediately",
    "zh": "无人机越出自定义作业区，请立即返航或降落"
  },
  "fpv_tip_0x0D37": {
    "en": "RTK error. Flight mission cannot be executed. Please check RTK settings",
    "zh": "RTK异常，无法执行飞行任务，请检查RTK设置"
  },
  "fpv_tip_0x0D38": {
    "en": "Mission paused due to RTK status fluctuation",
    "zh": "RTK状态跳变，已暂停任务"
  },
  "fpv_tip_0x0D39": {
    "en": "Mission exited. Please check RTK settings",
    "zh": "任务已退出，请检查RTK设置"
  },
  "fpv_tip_0x0D40": {
    "en": "SLAM map file load failed. Check or re-upload the file.",
    "zh": "Slam地图文件加载失败，请重新上传或检查"
  },
  "fpv_tip_0x0D41": {
    "en": "Aircraft outside custom operation zone. Takeoff prohibited",
    "zh": "飞机在自定义作业区外，禁止起飞"
  },
  "fpv_tip_0x0D41_in_the_sky": {
    "en": "Aircraft outside custom operation zone. Takeoff prohibited if the aircraft is on ground. Land immediately if it is airborne.",
    "zh": "飞机在自定义作业区外。若未起飞，禁止起飞；若已起飞，请立即降落。"
  },
  "fpv_tip_0x0D42": {
    "en": "Aircraft in buffer zone. Takeoff prohibited",
    "zh": "飞机在缓冲区，禁止起飞"
  },
  "fpv_tip_0x0D42_in_the_sky": {
    "en": "Aircraft near custom operation zone edge. Leave promptly.",
    "zh": "飞机靠近自定义作业区边缘，请尽快驶离"
  },
  "fpv_tip_0x0D43": {
    "en": "Aircraft in no-fly zone. Takeoff prohibited",
    "zh": "飞机在禁飞区，禁止起飞"
  },
  "fpv_tip_0x0D43_in_the_sky": {
    "en": "Aircraft in no-fly zone. Return to home or land promptly.",
    "zh": "飞机在禁飞区，请尽快返航或降落"
  },
  "fpv_tip_0x0D44": {
    "en": "Aircraft in buffer zone. Takeoff prohibited",
    "zh": "飞机在缓冲区，禁止起飞"
  },
  "fpv_tip_0x0D44_in_the_sky": {
    "en": "Aircraft near no-fly zone edge. Leave promptly",
    "zh": "飞机靠近禁飞区边缘，请尽快驶离"
  },
  "fpv_tip_0x0D45": {
    "en": "Aircraft out of custom operation zone. FTS triggered",
    "zh": "无人机已越出自定义作业区，FTS 已触发"
  },
  "fpv_tip_0x0D45_in_the_sky": {
    "en": "Aircraft entered no-fly zone. FTS triggered.",
    "zh": "飞机进入禁飞区，fts已触发"
  },
  "fpv_tip_0x0a72": {
    "en": "Poor video transmission signal, please adjust antenna angle",
    "zh": "图传信号弱，请改变天线角度"
  },
  "fpv_tip_0x0a73": {
    "en": "Video transmission signal interfered, please stay away from interference areas",
    "zh": "图传信号受到干扰，请远离干扰区域"
  },
  "fpv_tip_0x0a74": {
    "en": "Aircraft disconnected",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0a75": {
    "en": "Aircraft disconnectedr",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0a76": {
    "en": "Aircraft disconnected",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0a77": {
    "en": "Aircraft disconnected",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0a78": {
    "en": "Weak video transmission signal, please adjust antenna angle",
    "zh": "图传信号弱，请改变天线角度"
  },
  "fpv_tip_0x0a79": {
    "en": "Aircraft disconnected",
    "zh": "飞机连接断开"
  },
  "fpv_tip_0x0a7f": {
    "en": "Weak video transmission signal, please adjust antenna angle",
    "zh": "图传信号弱，请改变天线角度"
  },
  "fpv_tip_0x0a80": {
    "en": "Aircraft signal interfered",
    "zh": "飞机信号受到干扰"
  },
  "fpv_tip_0x0d01": {
    "en": "Please mark after takeoff",
    "zh": "请起飞后打点"
  },
  "fpv_tip_0x0d02": {
    "en": "Gimbal limit reached",
    "zh": "达到云台限位"
  },
  "fpv_tip_0x0d03": {
    "en": "Waypoint above aircraft",
    "zh": "标记点高于飞机"
  },
  "fpv_tip_0x10000801": {
    "en": "Please insert an SD card or switch to onboard storage",
    "zh": "请插入SD卡或者切换机载存储"
  },
  "fpv_tip_0x10000802": {
    "en": "Camera defogging via heating...",
    "zh": "镜头除雾加热中"
  },
  "fpv_tip_0x10000C01": {
    "en": "Remote ID anomaly, please comply with air traffic regulations during flight",
    "zh": "Remote ID异常，请遵守空管法规进行飞行"
  },
  "fpv_tip_0x10000C02": {
    "en": "Please enter Remote ID information according to local laws and regulations.",
    "zh": "根据当地法律法规的规定，请填写Remote ID信息"
  },
  "fpv_tip_0x10000C03": {
    "en": "Remote ID anomaly, takeoff prohibited according to local regulations",
    "zh": "Remote ID异常，根据当地法规禁止起飞"
  },
  "fpv_tip_0x10000C03_in_the_sky": {
    "en": "Remote ID anomaly. Land immediately",
    "zh": "Remote ID异常，请尽快降落"
  },
  "fpv_tip_0x20000B01": {
    "en": "Cooling fan error. Contact customer support.",
    "zh": "散热风扇故障，请联系售后处理"
  },
  "fpv_tip_0x20000C00": {
    "en": "Please enter UOM real-name registration flag",
    "zh": "请输入UOM实名登记标志"
  },
  "fpv_tip_0x20000D00": {
    "en": "Aircraft in no-fly zone. Takeoff prohibited",
    "zh": "飞机在禁飞区，禁止起飞"
  },
  "fpv_tip_0x20000D00_in_the_sky": {
    "en": "Aircraft in no-fly zone. Land immediately",
    "zh": "飞机在禁飞区，请立即降落"
  },
  "fpv_tip_0x20000D01": {
    "en": "Aircraft near edge of no-fly zone. Takeoff prohibited",
    "zh": "飞机靠近禁飞区边缘，禁止起飞"
  },
  "fpv_tip_0x20000D01_in_the_sky": {
    "en": "Aircraft near edge of no-fly zone. Leave promptly",
    "zh": "飞机靠近禁飞区边缘，请尽快驶离"
  },
  "fpv_tip_0x20000D02": {
    "en": "Aircraft in enhanced warning zone. Takeoff prohibited",
    "zh": "飞机在加强警示区，禁止起飞"
  },
  "fpv_tip_0x20000D02_in_the_sky": {
    "en": "Aircraft in enhanced warning zone. Land immediately",
    "zh": "飞机在加强警示区，请立即降落"
  },
  "fpv_tip_0x20000D03": {
    "en": "Aircraft near edge of enhanced warning zone. Takeoff prohibited",
    "zh": "飞机靠近加强警示区边缘，禁止起飞"
  },
  "fpv_tip_0x20000D03_in_the_sky": {
    "en": "Aircraft near edge of enhanced warning zone. Leave promptly",
    "zh": "飞机靠近加强警示区边缘，请尽快驶离"
  },
  "fpv_tip_0x20000D04": {
    "en": "Aircraft in authorization zone. Fly with caution",
    "zh": "飞机在授权区，请谨慎飞行"
  },
  "fpv_tip_0x20000D05": {
    "en": "Aircraft near edge of authorization zone. Fly with caution",
    "zh": "飞机靠近授权区边缘，请谨慎飞行"
  },
  "fpv_tip_0x20000D09": {
    "en": "Nest not found during landing, proceeding to alternate landing point.",
    "zh": "降落未找到机巢，正在前往备降点"
  },
  "fpv_tip_0x20000D09_in_the_sky": {
    "en": "Heading to alternate landing point",
    "zh": "启动前往备降点"
  },
  "fpv_tip_0x20000D0A": {
    "en": "Nest not found during landing. The alternate landing point is too far. Initiating forced landing.",
    "zh": "降落未找到机巢，备降点距离过远，将执行强制降落"
  },
  "fpv_tip_0x20000D0B": {
    "en": "Nest not found during landing, re-searching.",
    "zh": "降落未找到机巢，正在重新搜索"
  },
  "fpv_tip_0x20000D0C": {
    "en": "The gimbal rotation angle is too small, resulting in positioning failure. Please adjust the gimbal or move the drone",
    "zh": "云台转动过小，定位失败，请调整云台或移动无人机"
  },
  "fpv_tip_0x20000D0D": {
    "en": "Aircraft altitude exceeded 120m, which may violate local regulations.",
    "zh": "无人机飞行高度高于120m，可能违反当地法律"
  },
  "fpv_tip_0x20000D0E": {
    "en": "Aircraft does not meet takeoff conditions. Please check and try gain.",
    "zh": "无人机不满足起飞条件，请检查后再起飞"
  },
  "fpv_tip_0x20000D0F": {
    "en": "Sign the disclaimer and try again.",
    "zh": "请签署免责申明后重试"
  },
  "fpv_tip_0x20000D10": {
    "en": "The aircraft has exceeded the altitude/distance limit zone. Please check and try again.",
    "zh": "无人机已经超过了限高限远区，请检查后重试"
  },
  "fpv_tip_0x20000D11": {
    "en": "Laser rangefinder is not enabled. Position estimated based on visual positioning.",
    "zh": "未打开激光测距，使用视觉位置估计"
  },
  "fpv_tip_0x20000D13": {
    "en": "Route recovery completed",
    "zh": "当前航线已经恢复完成"
  },
  "fpv_tip_0x20500300": {
    "en": "The upper auxiliary light has automatically turned off due to excessive temperature. Please land immediately.",
    "zh": "上补光灯因温度过高已自动关闭，请立即降落"
  },
  "fpv_tip_0x30000000": {
    "en": "The aircraft attitude is abnormal, please place it on a flat site to re-check",
    "zh": "飞机姿态异常，请放置到平坦场地重新检测"
  },
  "fpv_tip_0x30000000_in_the_sky": {
    "en": "The aircraft attitude is abnormal",
    "zh": "飞机姿态异常"
  },
  "fpv_tip_0x30000001": {
    "en": "Heading not available, please contact dealer",
    "zh": "航向不可用，请联系经销商"
  },
  "fpv_tip_0x30000001_in_the_sky": {
    "en": "Heading not available",
    "zh": "航向不可用，请注意安全"
  },
  "fpv_tip_0x30000002": {
    "en": "The plane has flown to the maximum height",
    "zh": "飞机已飞到最大高度"
  },
  "fpv_tip_0x30000003": {
    "en": "The plane has flown the maximum distance",
    "zh": "飞机已飞到最远距离"
  },
  "fpv_tip_0x30000004": {
    "en": "Aircraft Approaching no-fly zone",
    "zh": "飞机靠近禁飞区"
  },
  "fpv_tip_0x30000005": {
    "en": "Aircraft in no-fly zone. Takeoff prohibited",
    "zh": "飞机在禁飞区，禁止起飞"
  },
  "fpv_tip_0x30000005_in_the_sky": {
    "en": "The aircraft is in a no-fly zone. Move away immediately",
    "zh": "飞机在禁飞区，请尽快远离"
  },
  "fpv_tip_0x30000006": {
    "en": "Aircraft approaching edge of custom operation zone",
    "zh": "飞机靠近自定义作业区边缘"
  },
  "fpv_tip_0x30000007": {
    "en": "Aircraft outside custom operation zone",
    "zh": "飞机在自定义作业区外"
  },
  "fpv_tip_0x30000008": {
    "en": "Aircraft approaching edge of authorization zone",
    "zh": "飞机靠近授权区边缘"
  },
  "fpv_tip_0x30000009": {
    "en": "The flight control CPU has exceeded 80℃/176℉, which affects the safety of the aircraft. Please turn off the aircraft and move to a cool and ventilated place to cool down",
    "zh": "飞控CPU已超过 80℃/176℉，影响飞机安全。请关闭飞机并移动到阴凉通风处进行降温"
  },
  "fpv_tip_0x30000009_in_the_sky": {
    "en": "The flight control CPU has exceeded 80℃/176℉, which affects the safety of the aircraft.",
    "zh": "飞控CPU温度高，已超过 80℃/176℉"
  },
  "fpv_tip_0x3000000A": {
    "en": "The temperature of the flight control board has exceeded 70℃/158℉, which affects the safety of the aircraft. Please turn off the aircraft and move to a cool and ventilated place to cool down",
    "zh": "飞控板温度已超过 70℃/158℉，影响飞机安全。请关闭飞机并移动到阴凉通风处进行降温"
  },
  "fpv_tip_0x3000000A_in_the_sky": {
    "en": "The temperature of the flight control board has exceeded 70℃/158℉, which affects the safety of the aircraft.",
    "zh": "飞控板温度已超过 70°C/158℉"
  },
  "fpv_tip_0x3000000B": {
    "en": "The flight control SD card is not working properly, please contact the dealer",
    "zh": "飞控SD卡工作异常，请联系经销商"
  },
  "fpv_tip_0x3000000B_in_the_sky": {
    "en": "The flight control SD card of the aircraft is working abnormally. Do you want to return to the flight?",
    "zh": "飞控SD卡工作异常"
  },
  "fpv_tip_0x3000000C": {
    "en": "The flight control fan works abnormally, please contact the dealer",
    "zh": "飞控风扇工作异常，请联系经销商"
  },
  "fpv_tip_0x3000000C_in_the_sky": {
    "en": "Aircraft flight control fan works abnormally",
    "zh": "飞控风扇工作异常"
  },
  "fpv_tip_0x3000000D": {
    "en": "Flight control software error, please contact the dealer",
    "zh": "飞控固件版本不匹配，请联系经销商"
  },
  "fpv_tip_0x3000000E": {
    "en": "The left wing is faulty, it is recommended to re-install the wing, if the re-installation fails, please contact the dealer",
    "zh": "左侧机翼故障，建议重装机翼，重装失败请联系经销商"
  },
  "fpv_tip_0x3000000E_in_the_sky": {
    "en": "Left wing failure",
    "zh": "左侧机翼故障"
  },
  "fpv_tip_0x3000000F": {
    "en": "The right wing is faulty, it is recommended to re-install the wing, if the re-installation fails, please contact the dealer",
    "zh": "右侧机翼故障，建议重装机翼，重装失败请联系经销商"
  },
  "fpv_tip_0x3000000F_in_the_sky": {
    "en": "Right wing failure",
    "zh": "右侧机翼故障"
  },
  "fpv_tip_0x30000010": {
    "en": "Initialization of navigation attitude is not complete",
    "zh": "导航姿态初始化未完成"
  },
  "fpv_tip_0x30000011": {
    "en": "Failed to update custom flight zone data",
    "zh": "未成功更新自定义飞行区"
  },
  "fpv_tip_0x30000012": {
    "en": "The GNSS is invalid, geo-awareness may be disabled",
    "zh": "导航位置不可用，地理感知可能会失效"
  },
  "fpv_tip_0x30000100": {
    "en": "Unbalanced battery, please contact dealer",
    "zh": "电池不平衡，请联系经销商"
  },
  "fpv_tip_0x30000101": {
    "en": "The front battery is missing, please install the battery in place",
    "zh": "飞机前电池缺失，请把电池安装到位"
  },
  "fpv_tip_0x30000101_in_the_sky": {
    "en": "Front battery missing. Returning to home.",
    "zh": "飞机前电池缺失，正在返航"
  },
  "fpv_tip_0x30000102": {
    "en": "The battery is missing after the plane, please install the battery in place",
    "zh": "飞机后电池缺失，请把电池安装到位"
  },
  "fpv_tip_0x30000102_in_the_sky": {
    "en": "Rear battery missing. Returning to home.",
    "zh": "飞机后电池缺失，正在返航"
  },
  "fpv_tip_0x30000103": {
    "en": "Aircraft battery temperature is too high. Do not take off",
    "zh": "飞机电池温度过高，请勿起飞"
  },
  "fpv_tip_0x30000103_in_the_sky": {
    "en": "Aircraft battery overtemperature",
    "zh": "飞机电池温度过高"
  },
  "fpv_tip_0x30000104": {
    "en": "Aircraft battery temperature is too low. Do not take off",
    "zh": "飞机电池温度过低，请勿起飞"
  },
  "fpv_tip_0x30000104_in_the_sky": {
    "en": "Aircraft battery undertemperature",
    "zh": "飞机电池温度过低"
  },
  "fpv_tip_0x30000105": {
    "en": "Aircraft battery temperature is low. Take off later",
    "zh": "飞机电池温度偏低，建议稍后起飞"
  },
  "fpv_tip_0x30000105_in_the_sky": {
    "en": "Low aircraft battery temperature",
    "zh": "飞机电池温度偏低"
  },
  "fpv_tip_0x30000106": {
    "en": "Front battery damaged. Replace the battery",
    "zh": "飞机前电池损坏，请更换电池"
  },
  "fpv_tip_0x30000107": {
    "en": "Rear battery damaged. Replace the battery",
    "zh": "飞机后电池损坏，请更换电池"
  },
  "fpv_tip_0x30000108": {
    "en": "The aircraft battery is damaged. Replace the battery",
    "zh": "飞机电池损坏，请更换电池"
  },
  "fpv_tip_0x30000109": {
    "en": "Front battery is self-heating due to its low temperature",
    "zh": "飞机前电池正在加热"
  },
  "fpv_tip_0x30000110": {
    "en": "Rear battery is self-heating due to its low temperature",
    "zh": "飞机后电池正在加热"
  },
  "fpv_tip_0x30000111": {
    "en": "Front battery temperature is below 25℃ /77℉ and battery level is lower than 60%. Do not take off",
    "zh": "飞机前电池温度低于25℃ /77℉，且电量低于60%，请勿起飞"
  },
  "fpv_tip_0x30000112": {
    "en": "Rear battery temperature is below 25℃ /77℉ and battery level is lower than 60%. Do not take off",
    "zh": "飞机后电池温度低于25℃ /77℉，且电量低于60%，请勿起飞"
  },
  "fpv_tip_0x30000113": {
    "en": "Battery temperature is below 25℃ /77℉ and battery level is lower than 60%. Do not take off",
    "zh": "电池温度低于25℃，且电量低于60%，请勿起飞"
  },
  "fpv_tip_0x30000200": {
    "en": "Elevator exception",
    "zh": "升降舵异常"
  },
  "fpv_tip_0x30000201": {
    "en": "The state of the aircraft motor ESC is abnormal",
    "zh": "飞机电机电调状态异常"
  },
  "fpv_tip_0x30000300": {
    "en": "Ultrasonic abnormalities, please contact the dealer",
    "zh": "超声波异常，请联系经销商"
  },
  "fpv_tip_0x30000301": {
    "en": "The airspeed meter is abnormal, go to calibration",
    "zh": "空速计异常，请校准"
  },
  "fpv_tip_0x30000301_in_the_sky": {
    "en": "Airspeed abnormal, the aircraft automatically enters the protect mode",
    "zh": "空速计异常，飞机自动进入保护模式"
  },
  "fpv_tip_0x30000302": {
    "en": "Weak GPS signal",
    "zh": "GPS信号弱"
  },
  "fpv_tip_0x30000303": {
    "en": "RTK signal weak",
    "zh": "RTK信号弱"
  },
  "fpv_tip_0x30000304": {
    "en": "Main IMU failure, please contact dealer",
    "zh": "主IMU故障，请联系经销商"
  },
  "fpv_tip_0x30000305": {
    "en": "Secondary IMU failure, please contact the dealer",
    "zh": "副IMU故障，请联系经销商"
  },
  "fpv_tip_0x30000306": {
    "en": "Compass failure, please contact dealer",
    "zh": "指南针故障，请联系经销商"
  },
  "fpv_tip_0x30000307": {
    "en": "Secondary Compass failure, please contact dealer",
    "zh": "备用指南针故障，请联系经销商"
  },
  "fpv_tip_0x30000308": {
    "en": "Barometer fault, please contact dealer",
    "zh": "气压计故障，请联系经销商"
  },
  "fpv_tip_0x30000309": {
    "en": "Secondary Barometer fault, please contact dealer",
    "zh": "备用气压计故障，请联系经销商"
  },
  "fpv_tip_0x3000030A": {
    "en": "RTK heading unlocked",
    "zh": "RTK航向未锁定"
  },
  "fpv_tip_0x3000030A_in_the_sky": {
    "en": "RTK heading abnormal",
    "zh": "RTK航向异常，请注意安全"
  },
  "fpv_tip_0x3000030B": {
    "en": "The airframe RTK antenna connection is disconnected, please turn off the aircraft, tighten the antenna, and then re-check the aircraft",
    "zh": "机身RTK天线连接断开， 请关闭飞机，拧紧天线，再重新进行机务检查"
  },
  "fpv_tip_0x3000030C": {
    "en": "The tail RTK antenna connection is disconnected, please turn off the aircraft, tighten the antenna, and re-check the aircraft",
    "zh": "机尾RTK天线连接断开， 请关闭飞机，拧紧天线，再重新进行机务检查"
  },
  "fpv_tip_0x3000030D": {
    "en": "The fuselage RTK antenna is short-circuited, please turn off the aircraft, tighten the antenna, and re-check the maintenance",
    "zh": "机身RTK天线短路， 请关闭飞机，拧紧天线，再重新进行机务检查"
  },
  "fpv_tip_0x3000030E": {
    "en": "The tail RTK antenna is short-circuited, please turn off the aircraft, tighten the antenna, and re-check the aircraft",
    "zh": "机尾RTK天线短路， 请关闭飞机，拧紧天线，再重新进行机务检查"
  },
  "fpv_tip_0x3000030F": {
    "en": "Forward sensing failure, please contact the dealer",
    "zh": "前向感知故障，请联系经销商"
  },
  "fpv_tip_0x30000310": {
    "en": "RTK communication exception",
    "zh": "RTK通讯异常"
  },
  "fpv_tip_0x30000311": {
    "en": "GPS communication abnormal",
    "zh": "GPS通讯异常"
  },
  "fpv_tip_0x30000312": {
    "en": "Basestation RTK information is invalid",
    "zh": "基站RTK信息无效"
  },
  "fpv_tip_0x30000313": {
    "en": "Basestation RTK heading2 information is invalid",
    "zh": "基站RTKHeading2信息不可用"
  },
  "fpv_tip_0x30000314": {
    "en": "Basestation RTK Heading information is invalid",
    "zh": "基站RTK航向信息不可用"
  },
  "fpv_tip_0x30000315": {
    "en": "Basestation location information is abnormal",
    "zh": "基站位置信息异常"
  },
  "fpv_tip_0x30000316": {
    "en": "Basestation speed information is abnormal",
    "zh": "基站速度信息异常"
  },
  "fpv_tip_0x30000317": {
    "en": "The base station attitude information is abnormal",
    "zh": "基站姿态信息异常"
  },
  "fpv_tip_0x30000318": {
    "en": "Mobile home point information is abnormal",
    "zh": "移动返航点信息异常"
  },
  "fpv_tip_0x30000319": {
    "en": "Invalid accuracy of moving home point information",
    "zh": "移动返航点信息精度差"
  },
  "fpv_tip_0x3000031A": {
    "en": "Magnetic heading deviation, please calibrate the compass away from strong magnetic fields",
    "zh": "磁航向出现偏差，请远离强磁场环境进行指南针校准"
  },
  "fpv_tip_0x3000031B": {
    "en": "Compass communication abnormal",
    "zh": "磁力计通讯异常"
  },
  "fpv_tip_0x3000031C": {
    "en": "Compass parameter update failed, please update again",
    "zh": "指南针参数更新失败，请重新更新"
  },
  "fpv_tip_0x3000031D": {
    "en": "Please restart the aircraft to complete the Air RTK module configuration.",
    "zh": "请重启飞机完成机载RTK工作模式配置"
  },
  "fpv_tip_0x30000400": {
    "en": "Image transmission exception",
    "zh": "图传异常"
  },
  "fpv_tip_0x30000400_in_the_sky": {
    "en": "Picture transmission disconnected",
    "zh": "图传断开连接"
  },
  "fpv_tip_0x30000401": {
    "en": "Aircraft not active",
    "zh": "飞机未激活"
  },
  "fpv_tip_0x30000402": {
    "en": "Actuator communication failure, please contact the dealer",
    "zh": "执行器通讯故障，请联系经销商"
  },
  "fpv_tip_0x30000403": {
    "en": "The aircraft flying height is too low, it will automatically adjust to a safe height",
    "zh": "飞机飞行高度过低，将自动调整到安全高度"
  },
  "fpv_tip_0x30000404": {
    "en": "The wings need to be calibrated. Please ensure both wings are installed properly before the calibration.\n- The left wing has to be calibrated",
    "zh": "机翼与飞机未配置，请先确认机翼正确，再进行配置\n- 飞机与左机翼未配置"
  },
  "fpv_tip_0x30000405": {
    "en": "The left wing is not compatible with the current fuselage. Please install the correct left wing. If the left wing is already correct, please contact your dealer.",
    "zh": "左机翼与当前机身无法配合使用，请安装正确的左机翼。若左机翼正确，请联系售后支持"
  },
  "fpv_tip_0x30000406": {
    "en": "There is an error in the connection to the left wing. Please ensure the left wing is installed properly and restart the aircraft. If the error persists after multiple restarts, please contact your dealer.",
    "zh": "左机翼连接出错，请先确认左机翼正确，再重启飞机。若多次重启仍出错，请联系售后支持"
  },
  "fpv_tip_0x30000407": {
    "en": "The wings need to be calibrated. Please ensure both wings are installed properly before the calibration.\n- The right wingl has to be calibrated",
    "zh": "机翼与飞机未配置，请先确认机翼正确，再进行配置\n- 飞机与右机翼未配置"
  },
  "fpv_tip_0x30000408": {
    "en": "The right wing is not compatible with the current fuselage. Please install the correct right wing. If the right wing is already correct, please contact your dealer.",
    "zh": "右机翼与当前机身无法配合使用，请安装正确的右机翼。若右机翼正确，请联系售后支持"
  },
  "fpv_tip_0x30000409": {
    "en": "The right wing is not compatible with the current fuselage. Please install the correct right wing. If the right wing is already correct, please contact your dealer.",
    "zh": "右机翼连接出错，请先确认右机翼正确，再重启飞机。若多次重启仍出错，请联系售后支持"
  },
  "fpv_tip_0x3000040A": {
    "en": "The wings need to be calibrated. Please ensure both wings are installed properly before the calibration.\n- The tail has to be calibrated",
    "zh": "机翼与飞机未配置，请先确认机翼正确，再进行配置\n- 飞机与尾翼未配置"
  },
  "fpv_tip_0x3000040B": {
    "en": "The tail is not compatible with the current fuselage. Please install the correct tail. If the tail is already correct, please contact your dealer.",
    "zh": "尾翼与当前机身无法配合使用，请安装正确的尾翼。若尾翼正确，请联系售后支持"
  },
  "fpv_tip_0x3000040C": {
    "en": "There is an error in the connection to the tail. Please ensure the tail is installed properly and restart the aircraft. If the error persists after multiple restarts, please contact your dealer.",
    "zh": "尾翼连接出错，请先确认尾翼正确，再重启飞机。若多次重启仍出错，请联系售后支持"
  },
  "fpv_tip_0x3000040D": {
    "en": "Airborne wind speed exceeds the limit",
    "zh": "空中风速超限"
  },
  "fpv_tip_0x3000040D_in_the_sky": {
    "en": "Airborne wind speed exceeds the limit. Execute RTH or alternate landing now.",
    "zh": "空中风速超限，请立即返航或备降"
  },
  "fpv_tip_0x30000500": {
    "en": "Aircraft battery is low, returning to home",
    "zh": "飞机电池电量低，正在返航"
  },
  "fpv_tip_0x30000501": {
    "en": "The aircraft is not in the designated country, flying to the takeoff point for diversion",
    "zh": "飞机不在可飞区内，正飞往起飞点备降"
  },
  "fpv_tip_0x30000502": {
    "en": "Airborne wind speed exceeds the limit",
    "zh": "空中风速超限"
  },
  "fpv_tip_0x30000502_in_the_sky": {
    "en": "Airborne wind speed exceeds the limit. Execute RTH or alternate landing now.",
    "zh": "空中风速超限，请立即返航或备降"
  },
  "fpv_tip_0x30000800": {
    "en": "No SD card detected, insert SD card",
    "zh": "无SD卡，请插入SD卡"
  },
  "fpv_tip_0x30000801": {
    "en": "SD card full, replace with new",
    "zh": "SD卡已满，请更换SD卡"
  },
  "fpv_tip_0x30000802": {
    "en": "SD card error, replace with new",
    "zh": "SD卡错误，请更换SD卡"
  },
  "fpv_tip_0x30000803": {
    "en": "SD card writing is slow. Format the SD card or replace it with a high-speed card",
    "zh": "SD卡写入慢，请格式化SD卡或更换高速卡"
  },
  "fpv_tip_0x30000804": {
    "en": "The onboard flash memory is full. Switch the storage location to the SD card",
    "zh": "机载闪存已满，请切换存储位置到SD卡"
  },
  "fpv_tip_0x30000805": {
    "en": "The onboard flash memory is abnormal. Format it or contact after-sales service.",
    "zh": "机载闪存异常，请格式化或联系售后处理"
  },
  "fpv_tip_0x30000806": {
    "en": "Unknown SD card file system. Format the SD card",
    "zh": "未知的SD卡文件系统，请格式化SD卡"
  },
  "fpv_tip_0x30000807": {
    "en": "The onboard flash memory is full. Clear the storage space",
    "zh": "机载闪存已满，请清理存储空间"
  },
  "fpv_tip_0x40000000": {
    "en": "The right wing is about to reach its service life",
    "zh": "右机翼即将达到使用寿命"
  },
  "fpv_tip_0x40000001": {
    "en": "The right wing has reached its service life, please replace it before flying again",
    "zh": "右机翼已达到使用寿命，请更换后再飞行"
  },
  "fpv_tip_0x40000002": {
    "en": "The left wing is about to reach its service life",
    "zh": "左机翼即将达到使用寿命"
  },
  "fpv_tip_0x40000003": {
    "en": "The left wing has reached its service life, please replace it before flying again",
    "zh": "左机翼已达到使用寿命，请更换后再飞行"
  },
  "fpv_tip_0x40000004": {
    "en": "The tail wing is about to reach its service life",
    "zh": "尾翼即将达到使用寿命"
  },
  "fpv_tip_0x40000005": {
    "en": "The tail wing has reached its service life, please replace it before flying again",
    "zh": "尾翼已达到使用寿命，请更换后再飞行"
  },
  "fpv_tip_0x40000100": {
    "en": "The front battery is about to reach its service life",
    "zh": "前电池即将到达使用寿命"
  },
  "fpv_tip_0x40000101": {
    "en": "The front battery has reached its service life, please replace it before flying again",
    "zh": "前电池已达到使用寿命，请更换后再飞行"
  },
  "fpv_tip_0x40000102": {
    "en": "The back battery is about to reach its service life",
    "zh": "后电池即将到达使用寿命"
  },
  "fpv_tip_0x40000103": {
    "en": "The back battery has reached its service life, please replace it before flying again",
    "zh": "后电池已达到使用寿命，请更换后再飞行"
  }
}